Whether you’re really passionate about RPC, MQTT, Matrix or wayland, tell us more about the protocols or open standards you have strong opinions on!
Whether you’re really passionate about RPC, MQTT, Matrix or wayland, tell us more about the protocols or open standards you have strong opinions on!
IPv6. Lack of IPv4 addresses it’s a problem, specially in poorer countries. But still lots of servers and ISPs don’t support it natively. And what is worse. Lots of sysadmins don’t want to learn it.
Am sysadmin, can confirm I don’t wanna learn it.
Also a sysasmin, really don’t wanna learn it…or have to type it on the daily
not a sysadmin, but i admin a system or two, have yet to learn it myself, but will eventually learn it.
My university recently had Internet problems, where the DHCP only leased Out ipv6 addresses. For two days, we could all see which sites implemented ipv6 and which didn’t.
Many big corpo sites like GitHub or discord Apperently don’t. Small stuff like my personal website or https://suikagame.com do.
github is so stupid with that, it’s actually funny
That’s a fun little game there!
Lots of really large sites are horribly misconfigured. I had intermittent issues because one of the edge hosts in Netflix ‘s round robin dns did not do MTU discovery properly.
IPv6 is great, but NAT is quite functional and is prolonging the demise of IPv4.
deleted by creator
You can have that with ipv6, too.
NAT is not for security, that’s what the firewall is for. Nobody can access your IPv6 network unless you allow access through the firewall.
I don’t think they were talking about access to the network.
“The inside of the network stay anonymous” sounds like they are talking about internet access to the internal network.
If computers connect to others through the internet, the IPv6 address can reveal how many computers there are on the local network, and if certain traffic to different destinations are coming from the same computer, but also if one of the computers has gone offline but then resumes from sleep/hibernation.
To me their comment means they want to avoid that, and I agree, I want to avoid that too. To fix these, I would need to configure NAT on my router for IPv6.
Yes IPv6 address privacy extensions help somewhat, but
With v4 addresses these did not really matter, because everything was being sent from the same public IP, and and outside observer could only see what a “network” is doing collectively. But with v6 an address identifies a computer, across websites/services. Even if it’s just for a "short’ time, even if the address is randomized.
If you want privacy, you need some kind of VPN or onion routing. Even if everything you list were correct, the difference between IPv4 and 6 for privacy would be marginal.
I don’t think this is so black and white. I’m a regular tor user, but so often it’s not worth it to load webpages through a dial-up connection, and then there are the sites that block access for tor users for some reason.
Which parts weren’t?
I disagree
You’re thinking of a firewall. NAT is just the thing that makes a connection appear to come from an IP on the internet when it’s really coming from your router, and it’s not needed with IPv6. But you would not see any difference with IPv6 without it.
That connection only “appears to come from” if I explicitly put a rule in my NAT table directing it to my computer behind the router doing the NAT-ing.
Otherwise all connections through NAT are started from internal->external network requests and the state table in NAT keeps track of which internal IP is talking to which external IP and directs traffic as necessary.
So OP is correct, it does apply a measure of security. Port scanning someone behind NAT isn’t possible, you just end up port scanning their crappy NAT router provided by their ISP unless they have specifically opened up some ports and directed them to their internal IP address.
Compare this to IPV6 where you get a slice of the public address space to place your devices in and they are all directly addressable. In that case your crappy ISP router also is a “proper” firewall. Strangely enough it usually is a “stateful” firewall with default deny-all rules that tracks network connections and looks and performs almost exactly like the NAT version, just without address translation.
You end up just port scanning their crappy router on IPv6 as well because ports that are not opened are stuck at the firewall either way, no matter if you use IPv4 or IPv6.
Just because every device gets a public IP does not mean that IP is publicly accessible.
An advantage that IPv6 has against port scanning is the absurdly large network sizes. For example, my ISP gives me a /56 prefix, that is 4,722,366,482,869,645,213,696 IPv6 addresses. Good luck finding the used ones with the port open you need.
Even with just a /64 prefix you get 18,446,744,073,709,551,616 addresses, way outside the feasibility of port scanning.
realistically, it wouldnt surprise me if ISPs started NATing on residential IPV6 networks, just for the simplicity, but still allowed end users to assign their own IPs if they so pleased. Given the surge in shitty IOT devices, that’s probably a good thing for most people. Though a firewall would also accomplish this as well.
Found the guy that does not want to learn IPv6!
No. Stop spreading that myth. NAT does fuck all for security. If you want a border gateway, you can just have a border gateway.
you know what is more secure? Not being connected to the internet.
My isp decided to put me behind a CGNAT and broke my access to my network from outside my network. Wanted to charge me $5 a month to get around it. It’s not easy to get around for a layman, but possible. More than anything it just pissed me off that I’d have to pay for something that 1 day ago was free.
How can you bypass CGNAT?
Set up a reverse proxy on another machine (like one of those free oracle cloud things). I can’t go into detail because I don’t know exactly how. I think cloudflare also has options for that for free. Either way it’s annoying.
Cloudflare tunnel, and its alternatives, such as localXpose, altho the privacy is probably questionable, and a many of them require a domain.
NAT is functional as long as you like NAT, which im pretty sure nobody likes, so uh.
Plenty of people like NAT.
the only people that like nat are network admins, and ISPs.
Everyone else hates them. The rest don’t care, but they wouldn’t know a NAT if it hit them in the face.
Say this to my very large Canadian ISP who still doesn’t support IPv6 for residential customers. Last I checked, adoption in Canada was still under 50%.
50%?? I fucking wish. In Spain we are at 5%. I finally got IPv6 in my phone this year, but I want it in my home, which is still only available as IPv4 even if they’re the same ISP.